雷达生命探测仪Radar-2D中英

雷达生命探测仪

     本产品是一款综合毫米波雷达技术和生物医学工程技术研制而成的生命体征目标探测设备，原理是基于活动物体会使回波产生多普勒效应，通过高敏天线接收信号、智能识别芯片的分析、定位算法完成对目标的实时跟踪，并将有用的信息在屏幕上进行呈现。该探测仪重量轻，体积小，操作简单，可单兵配备，广泛用于军事侦查、消防救援、安检搜查等任务。

一、功能特点：

1、一键操作，3秒进入工作状态。

2、系统有自检功能，可对检出故障进行提示。

3、可对墙后移动目标实时进行左、中、右跟踪定位；

4、抗干挠：位于操作侧的人员正常活动不影响雷达工作，对非前方目标引起的干挠性报警有排除及提示功能。

5、静音模式：无噪音动态显示探测信息、雷达状态，便于隐匿侦查。

6、可识别是否为金属墙面或钢架结构墙体，以便寻找墙体的薄弱处进行更有效的探测。

二、产品参数：
◆执行GB 4943.1-2022《信息和通信技术设备 第一部分》标准，并获得国家认可的认证检测机构出具的检测报告；
◆探测距离：≤30米
◆穿墙厚度：≤30厘米（砖块、岩石、非金属等墙体）
◆探测角度：120度
◆屏幕：7寸液晶屏
◆工作电源：电压5V，内置5000mA锂电池（续航约10小时）；
◆配置：主机+支架+充电器+铝盒外箱；
◆外形尺寸：长400mmx300mmx50mm

◆外箱尺寸：长460mmx390mmx170mm
◆产品重量：7kg（含铝箱）

3.       操作说明：
1、使用前请先将支架与主机相连（或直接将主机置于可固定位置处），然后将探测面贴紧墙体（注：必要时可先使用墙体金属探测器探测是否为钢架结构墙），调整支架使其不会晃动即可。

2、       单按开关按钮开机，电源指示灯亮起，并进行2秒系统自检，正常屏幕将会提示“自检成功”，如遇故障，屏幕会提示“自检失败”。

3、       开机后，探测中请勿触碰机器，可站于机器后方静心观察，如有误碰撞，机器将显示“请勿晃动雷达”，此时等待机器重新稳固即可。
4、探测到目标后，屏幕会根据目标方位，按左、中、右进行区分显示。
5、产品为充电配置，接口位于主机底部，接口旁小孔为指示灯，其中红灯充电中，绿灯为充满，正常4小时可充满，充满续航约10小时。

6、使用完请直接按开关机键以节约电量，如遇电量不足会自动关机，并导致无法正常开机。

四 、注意事项
1、需贴墙使用，以免信号泄露导致观察人员影响探测效果！
2、大型建筑物的承重墙无法穿透！

Radar Life Detector

This product is a comprehensive life sign detection device developed through the integration of millimeter-wave radar technology and biomedical engineering. The principle is based on the Doppler effect generated by moving objects, where the echo is received through a high-sensitivity antenna. The intelligent recognition chip analyzes the signal, and a positioning algorithm accomplishes real-time tracking of the target. The useful information is then presented on the screen. The detector is lightweight, compact, easy to operate, suitable for individual deployment, and widely used in military reconnaissance, firefighting and rescue, security inspections, and search missions.

I. Features:

1. One-key operation, enters working state in 3 seconds.

2. The system has a self-check function to prompt for detected malfunctions.

3. Real-time left, center, and right tracking and positioning of moving targets behind walls.

4. Anti-interference: Normal activities on the operational side do not affect radar operation. There is exclusion and alert functionality for interference alarms caused by non-frontal targets.

5. Silent mode: Displays detection information and radar status without noise, facilitating covert reconnaissance.

6. Can identify whether it is a metal wall or a steel frame structure wall to locate weak points for more effective detection.

II. Product Parameters:

◆ Conforms to the standard GB 4943.1-2022 "Information Technology Equipment - Safety - Part 1" and has obtained a testing report from a nationally recognized certification testing institution.

◆ Detection Distance: ≤30 meters

◆ Wall Penetration Thickness: ≤30 centimeters (brick, rock, non-metal walls, etc.)

◆ Detection Angle: 120 degrees

◆ Screen: 7-inch LCD screen

◆ Power Supply: Voltage 5V, built-in 5000mAh lithium battery (approximately 10 hours of endurance);

◆ Configuration: Main unit + bracket + charger + aluminum case outer box;

◆ Dimensions: Length 400mm x 300mm x 50mm

◆ Outer Box Dimensions: Length 460mm x 390mm x 170mm

◆ Product Weight: 7kg (including aluminum case)

III. Operation Instructions:

1. Before use, connect the bracket to the main unit (or place the main unit in a fixed position directly), then place the detection surface close to the wall (Note: use a wall metal detector if necessary to check for a steel frame structure wall). Adjust the bracket to prevent shaking.

2. Turn on the power with a single press of the switch button. The power indicator light will illuminate, and a 2-second system self-check will be performed. A normal screen will display "Self-check successful," and in case of a failure, the screen will show "Self-check failed."

3. After turning on, do not touch the machine during detection. You can stand behind the machine and observe quietly. If there is a collision, the machine will display "Do not shake the radar," and wait for the machine to stabilize again.

4. After detecting the target, the screen will display differentiation according to the target's direction: left, center, or right.

5. The product is equipped with charging. The interface is at the bottom of the main unit, and there is an indicator light next to the interface. The red light indicates charging, and the green light indicates full charge. It takes about 4 hours to fully charge, providing approximately 10 hours of endurance when full.

6. After use, please press the power switch directly to save power. In case of insufficient battery, the machine will shut down automatically, resulting in the inability to start normally.

IV. Precautions:

1. Stick to the wall during use to avoid signal leakage affecting the detection effect for observers!

2. Cannot penetrate load-bearing walls of large buildings!